Beolab to Receivers

The ET-3 is a handy little device that improves the flexibility of the basic trigger functionality on your preamp or processor.

The ET-3 has one trigger input and three high current trigger outputs. If your source unit has a trigger output, simply use the provided trigger cable to connect its trigger output to the trigger input on the ET-3, then connect the trigger outputs on the ET-3 to up to three trigger-enabled devices. When your source device switches its trigger output status to On, the three trigger outputs on the ET-3 will follow that signal, and each of the trigger outputs on the ET-3 will send the On signal to the device connected to it. (So, for example, you can use the ET-3 to enable the single trigger output on your preamp to turn on three trigger enabled amplifiers at the same time.)

The ET-3 can also be configured to send trigger signals to up to three connected devices as soon as it is powered on. You can then plug the power supply for the ET-3 into any powered outlet on a remote controlled power strip or piece of stereo equipment. As soon as the ET-3 receives power, it will send trigger signals to turn on the trigger-enabled equipment connected to its outputs.

Power supply has US connection! 
Latest item, out of stock!

Mono cable for the right channel.

1 X Pre-out right (Tulp)

1 X DC-12V minijack connector (trigger)

1 X DIN8 Female (powerlink in)

* Not for Beolab 5, 50, 90 beolink passive.

 Specification:
• Mono version (RIGHT)
• Gold-plated RCA male connector (Audio)
• Gold-plated mini-jack male connector (12V Trigger)
• 8-pin DIN Powerlink female connector (Audio + Trigger)
• Audio cable of good quality
• 12V to 4,5V Step Down (BANG & OLUFSEN Powerlink protection)

 Mono cable for the left channel.

1 X Pre-out left (Tulp)

1 X DC-12V minijack connector (trigger)

1 X DIN8 Female (powerlink in)

* Not for Beolab 5, 50, 90 beolink passive.

 Specification:
• Mono version (LEFT)
• Gold-plated RCA male connector (Audio)
• Gold-plated mini-jack male connector (12V Trigger)
• 8-pin DIN Powerlink female connector (Audio + Trigger)
• Audio cable of good quality
• 12V to 4,5V Step Down (BANG & OLUFSEN Powerlink protection)

Hum or noise across the trigger jack?
Try to put this lead between the trigger, disconnect the ground.

Specification:
• Mono version (SUB / CENTER)
• Gold-plated RCA male connector (Audio)
• Gold-plated mini-jack male connector (12V Trigger)
• 8-pin DIN Powerlink female connector (Audio + Trigger)
• Audio cable of good quality
• 12V to 4,5V Step Down (BANG & OLUFSEN Powerlink protection)

Hum or noise across the trigger jack?
Try to put this lead between the trigger, disconnect the ground.

BANG & OLUFSEN compatible adapter cable based on the audio cable in good quality,

fitted with gold-plated 3.5mm stereo mini-jack for analog audio and trigger cable,

fitted with a USB connector, for use of USB "trigger" from eg PC, MAC,

USB Power supply or anything that could supply via USB.

The cable comes out in an 8-pin DIN female connector

that allows for the continuation signals in existing or new Powerlink cables and you are using 2 Powerlink cables,

you can split the signal with a Powerlink split cable Y cable.

NOT be used for BeoLab 5, 50 and 90.

Trigger hum or noise is common when connecting cables to a receiver, especially with certain amplifiers such as Marantz, Denon and Rotel.

This Trigger Power Adapter solves the hum problem by separating the ground.

This cable makes it possible to use the Trigger Splitter to power up to 6 Beolab Speakers with only 1 Trigger output from the amplifier/receiver.
By connecting this cable to the Trigger output and connecting all other trigger plugs, the amplifier will turn on the B&O speakers, which would otherwise not turn on automatically due to the lack of continuous voltage.

Hum or noise across the trigger jack?
Try to put this lead between the trigger, disconnect the ground.

1x RCA + 3,5 mm Trigger to Powerlink Female, stereo audio adaptor

1x RCA + 3,5 mm Trigger to Powerlink Female, mono audio adaptor, right

1x RCA + 3,5 mm Trigger to Powerlink Female, mono audio adaptor, left

2x RCA + 3,5 mm Trigger to Powerlink Female, mono audio adaptor, center/sub

Set have 5 Powerlink Female Connections 

This set is the trigger for 6 splitter - Adapter cable recommended,
because most receivers but one trigger output has.

If you suffer from Brom, connect this Isolator between the Tulip (RCA) wiring.

Simple and easy, disconnect the tulip cable from TV or sonos / amplifier and connect this isolator, then connect the cables to the isolator and the hum is gone.

Connection, 2 x tulip (left / right) 2 x female tulip (left / right) (no power needed)

This cable is used to still be able to connect to a second speaker . BeoLab speaker with a 1 input , ( eg beolab3 )
 

The white / silver Din plug behind the beolab3 speaker , two others in the Powerlink cables. ready.

Also possible with Powerlink splitter 1 to 5 for connection 5 beolabs to one connection, scroll down for these connector

Cable is 3,5 mm thick and not shielded.

Powerlink Y cable shielded, scroll down.

Have your TV has a headphone output and USB?

Use the USB cable and 1 Powerlink Y-cable.

To this you can connect 2 power link cables.

How it works,

Connect the USB (trigger) cable to the USB port of your TV (0.5V Trigger) connect the 3.5mm mini-jack to the headphone output, stop now the Y cable into the female v / d cable.

Now you can connect 2 power link cables to your existing speakers to BeoLab.

(often in the TV menu, you need to activate the headphone)

prices,

USB (trigger) cable € 37,50 euro

Powerlink Y-cable € 20,00 euro

Not for beolab 5, 50 and 90